1015.06.2 Adhesive Requirements: Sheeting shall have a pre -
coated pressure sensitive adhesive backing, which may be applied without additional coats on either sheeting or application surface. Adhesive shall comply with ASTM D4956, Class 1 (pressure sensitive).
1015.06.3 Physical Characteristics: The film shall be readily cut
by normal fabricating methods without cracking, checking or flaking. Applied film shall be fr ee from ragged edges, cracks, and blisters. The material shall have demonstrated its ability to withstand normal weathering without checking, cracking, or excessive color loss.
1015.07 Sign Enamels, Paints , Silk Screen Paste, and
OVERLAY FILM.
1015.07.1 Sign Enamels and Paints: These shall be applied in
accordance with the sheeting manufacturer's recommendations . Final appearance as well as materials used shall be subject to approval.
1015.07.2 Silk Screen Paste: Silk screen paste shall be mixed at
the factory, well ground t o a uniform consistency and smooth texture, and shall be free from water and other foreign matter. It shall dry within 18 hours to a film that does not run, streak, or sag. Paste which has livered, hardened, or thickened in the container, or in which pig ment has settled out so that it cannot be readily broken up with a paddle to a uniform usable consistency, will be rejected. Thinner shall be used in accordance with the sheeting manufacturer's recommendations. Paste shall have proper pigmentation and co nsistency for use in silk screen equipment. The material shall produce the desired color and the same retroreflectivity values as required for reflective sheeting of the same type and color when applied on reflective sheeting background. Paste shall meet the quality and test requirements for appearance, coarse particles, and moisture and water resistance as specified for sign paints.
1015.07.3 Overlay Film: Transparent electronic cuttable overlay
film shall produce the desired color and the same reflectivity val ues as required for reflective sheeting of the same type and color when applied on reflective sheeting background .
1015.06.2 Adhesive Requirements: Sheeting shall have a pre -
coated pressure sensitive adhesive backing, which may be applied without additional coats on either sheeting or application surface. Adhesive shall comply with ASTM D4956, Class 1 (pressure sensitive).
1015.06.3 Physical Characteristics: The film shall be readily cut
by normal fabricating methods without cracking, checking or flaking. Applied film shall be fr ee from ragged edges, cracks, and blisters. The material shall have demonstrated its ability to withstand normal weathering without checking, cracking, or excessive color loss.
1015.07 Sign Enamels, Paints , Silk Screen Paste, and
OVERLAY FILM.
1015.07.1 Sign Enamels and Paints: These shall be applied in
accordance with the sheeting manufacturer's recommendations . Final appearance as well as materials used shall be subject to approval.
1015.07.2 Silk Screen Paste: Silk screen paste shall be mixed at
the factory, well ground t o a uniform consistency and smooth texture, and shall be free from water and other foreign matter. It shall dry within 18 hours to a film that does not run, streak, or sag. Paste which has livered, hardened, or thickened in the container, or in which pig ment has settled out so that it cannot be readily broken up with a paddle to a uniform usable consistency, will be rejected. Thinner shall be used in accordance with the sheeting manufacturer's recommendations. Paste shall have proper pigmentation and co nsistency for use in silk screen equipment. The material shall produce the desired color and the same retroreflectivity values as required for reflective sheeting of the same type and color when applied on reflective sheeting background. Paste shall meet the quality and test requirements for appearance, coarse particles, and moisture and water resistance as specified for sign paints.
1015.07.3 Overlay Film: Transparent electronic cuttable overlay
film shall produce the desired color and the same reflectivity val ues as required for reflective sheeting of the same type and color when applied on reflective sheeting background .
1015.06.2 Adhesive Requirements: Sheeting shall have a pre -
coated pressure sensitive adhesive backing, which may be applied without additional coats on either sheeting or application surface. Adhesive shall comply with ASTM D4956, Class 1 (pressure sensitive).
1015.06.3 Physical Characteristics: The film shall be readily cut
by normal fabricating methods without cracking, checking or flaking. Applied film shall be fr ee from ragged edges, cracks, and blisters. The material shall have demonstrated its ability to withstand normal weathering without checking, cracking, or excessive color loss.
1015.07 Sign Enamels, Paints , Silk Screen Paste, and
OVERLAY FILM.
1015.07.1 Sign Enamels and Paints: These shall be applied in
accordance with the sheeting manufacturer's recommendations . Final appearance as well as materials used shall be subject to approval.
1015.07.2 Silk Screen Paste: Silk screen paste shall be mixed at
the factory, well ground t o a uniform consistency and smooth texture, and shall be free from water and other foreign matter. It shall dry within 18 hours to a film that does not run, streak, or sag. Paste which has livered, hardened, or thickened in the container, or in which pig ment has settled out so that it cannot be readily broken up with a paddle to a uniform usable consistency, will be rejected. Thinner shall be used in accordance with the sheeting manufacturer's recommendations. Paste shall have proper pigmentation and co nsistency for use in silk screen equipment. The material shall produce the desired color and the same retroreflectivity values as required for reflective sheeting of the same type and color when applied on reflective sheeting background. Paste shall meet the quality and test requirements for appearance, coarse particles, and moisture and water resistance as specified for sign paints.
1015.07.3 Overlay Film: Transparent electronic cuttable overlay
film shall produce the desired color and the same reflectivity val ues as required for reflective sheeting of the same type and color when applied on reflective sheeting background .
1015.06.2 Adhesive Requirements: Sheeting shall have a pre -
coated pressure sensitive adhesive backing, which may be applied without additional coats on either sheeting or application surface. Adhesive shall comply with ASTM D4956, Class 1 (pressure sensitive).
1015.06.3 Physical Characteristics: The film shall be readily cut
by normal fabricating methods without cracking, checking or flaking. Applied film shall be fr ee from ragged edges, cracks, and blisters. The material shall have demonstrated its ability to withstand normal weathering without checking, cracking, or excessive color loss.
1015.07 Sign Enamels, Paints , Silk Screen Paste, and
OVERLAY FILM.
1015.07.1 Sign Enamels and Paints: These shall be applied in
accordance with the sheeting manufacturer's recommendations . Final appearance as well as materials used shall be subject to approval.
1015.07.2 Silk Screen Paste: Silk screen paste shall be mixed at
the factory, well ground t o a uniform consistency and smooth texture, and shall be free from water and other foreign matter. It shall dry within 18 hours to a film that does not run, streak, or sag. Paste which has livered, hardened, or thickened in the container, or in which pig ment has settled out so that it cannot be readily broken up with a paddle to a uniform usable consistency, will be rejected. Thinner shall be used in accordance with the sheeting manufacturer's recommendations. Paste shall have proper pigmentation and co nsistency for use in silk screen equipment. The material shall produce the desired color and the same retroreflectivity values as required for reflective sheeting of the same type and color when applied on reflective sheeting background. Paste shall meet the quality and test requirements for appearance, coarse particles, and moisture and water resistance as specified for sign paints.
1015.07.3 Overlay Film: Transparent electronic cuttable overlay
film shall produce the desired color and the same reflectivity val ues as required for reflective sheeting of the same type and color when applied on reflective sheeting background .
1015.06.2 Adhesive Requirements: Sheeting shall have a pre -
coated pressure sensitive adhesive backing, which may be applied without additional coats on either sheeting or application surface. Adhesive shall comply with ASTM D4956, Class 1 (pressure sensitive).
1015.06.3 Physical Characteristics: The film shall be readily cut
by normal fabricating methods without cracking, checking or flaking. Applied film shall be fr ee from ragged edges, cracks, and blisters. The material shall have demonstrated its ability to withstand normal weathering without checking, cracking, or excessive color loss.
1015.07 Sign Enamels, Paints , Silk Screen Paste, and
OVERLAY FILM.
1015.07.1 Sign Enamels and Paints: These shall be applied in
accordance with the sheeting manufacturer's recommendations . Final appearance as well as materials used shall be subject to approval.
1015.07.2 Silk Screen Paste: Silk screen paste shall be mixed at
the factory, well ground t o a uniform consistency and smooth texture, and shall be free from water and other foreign matter. It shall dry within 18 hours to a film that does not run, streak, or sag. Paste which has livered, hardened, or thickened in the container, or in which pig ment has settled out so that it cannot be readily broken up with a paddle to a uniform usable consistency, will be rejected. Thinner shall be used in accordance with the sheeting manufacturer's recommendations. Paste shall have proper pigmentation and co nsistency for use in silk screen equipment. The material shall produce the desired color and the same retroreflectivity values as required for reflective sheeting of the same type and color when applied on reflective sheeting background. Paste shall meet the quality and test requirements for appearance, coarse particles, and moisture and water resistance as specified for sign paints.
1015.07.3 Overlay Film: Transparent electronic cuttable overlay
film shall produce the desired color and the same reflectivity val ues as required for reflective sheeting of the same type and color when applied on reflective sheeting background .
1015.08 Temporary Pavement M Arkings.
1015.08.1 Temporary Tape: Temporary tape shall comply with
ASTM D4592, Type I (removable) or Type II (non -removable) an d shall be from the Approved Materials List.
1015.08.2 Painted Stripe: Paint shall be an approved traffic paint
complying with 1015.12 . Glass beads for drop -on applicati on shall comply with 1015.13.
1015.08.3 Temporary Raised Pavement Markings for Asphalt
Surface Treatment: Temporary raised pavement markers for asphalt surface treatment s hall be flexible reflective tabs having a nominal width of 4 inches. The markers shall be yellow with amber reflective area on both sides. The body of the marker shall consist of a base and vertical wall made of polyurethane or other approved material and shall be capable of maintaining a reasonable vertical position after installation. The initial minimum Coefficient of Luminous Intensity at an entrance angle of -4 degrees and an observation angle of 0.2 degrees shall be 230 mcd/lx when measured in accor dance with ASTM E810. The reflective material shall be protected with an easily removable cover of heat resistant material capable of withstanding and protecting the reflective material from the application of asphalt at temperatures exceeding 325°F.
1015.09 RAISED PAVEMENT MARK ERS. Markers shall be either
non-reflectorized or reflectorized, as specified. Markers shall be from the Approved Materials List.
1015.09.1 Non-Reflectorized Markers:
1015.09.1 1 Description: Non-reflectorized markers shall
consist of an acrylonitrile butadiene styrene polymer or other approved material, and shall be approximately 4 x 6 -inches.
1015.09.1 2 Physical Requirements: Markers shall comply
with the compressive strength requirements of ASTM D4280. The color shall be in accordance with the plans and the MUTCD.
1015.09.2 Reflectorized Markers: Reflectorized markers shall
comply with ASTM D4280, Designation H and Designation F. The type and color shall be in accordance with the plans and the MUTCD. The markers shall be either standard having minim um base dimensions of 3 x 3 - inches and a maximum height of 0.80 inches or low profile having
1015.08 Temporary Pavement M Arkings.
1015.08.1 Temporary Tape: Temporary tape shall comply with
ASTM D4592, Type I (removable) or Type II (non -removable) an d shall be from the Approved Materials List.
1015.08.2 Painted Stripe: Paint shall be an approved traffic paint
complying with 1015.12 . Glass beads for drop -on applicati on shall comply with 1015.13.
1015.08.3 Temporary Raised Pavement Markings for Asphalt
Surface Treatment: Temporary raised pavement markers for asphalt surface treatment s hall be flexible reflective tabs having a nominal width of 4 inches. The markers shall be yellow with amber reflective area on both sides. The body of the marker shall consist of a base and vertical wall made of polyurethane or other approved material and shall be capable of maintaining a reasonable vertical position after installation. The initial minimum Coefficient of Luminous Intensity at an entrance angle of -4 degrees and an observation angle of 0.2 degrees shall be 230 mcd/lx when measured in accor dance with ASTM E810. The reflective material shall be protected with an easily removable cover of heat resistant material capable of withstanding and protecting the reflective material from the application of asphalt at temperatures exceeding 325°F.
1015.09 RAISED PAVEMENT MARK ERS. Markers shall be either
non-reflectorized or reflectorized, as specified. Markers shall be from the Approved Materials List.
1015.09.1 Non-Reflectorized Markers:
1015.09.1 1 Description: Non-reflectorized markers shall
consist of an acrylonitrile butadiene styrene polymer or other approved material, and shall be approximately 4 x 6 -inches.
1015.09.1 2 Physical Requirements: Markers shall comply
with the compressive strength requirements of ASTM D4280. The color shall be in accordance with the plans and the MUTCD.
1015.09.2 Reflectorized Markers: Reflectorized markers shall
comply with ASTM D4280, Designation H and Designation F. The type and color shall be in accordance with the plans and the MUTCD. The markers shall be either standard having minim um base dimensions of 3 x 3 - inches and a maximum height of 0.80 inches or low profile having
1015.08 Temporary Pavement M Arkings.
1015.08.1 Temporary Tape: Temporary tape shall comply with
ASTM D4592, Type I (removable) or Type II (non -removable) an d shall be from the Approved Materials List.
1015.08.2 Painted Stripe: Paint shall be an approved traffic paint
complying with 1015.12 . Glass beads for drop -on applicati on shall comply with 1015.13.
1015.08.3 Temporary Raised Pavement Markings for Asphalt
Surface Treatment: Temporary raised pavement markers for asphalt surface treatment s hall be flexible reflective tabs having a nominal width of 4 inches. The markers shall be yellow with amber reflective area on both sides. The body of the marker shall consist of a base and vertical wall made of polyurethane or other approved material and shall be capable of maintaining a reasonable vertical position after installation. The initial minimum Coefficient of Luminous Intensity at an entrance angle of -4 degrees and an observation angle of 0.2 degrees shall be 230 mcd/lx when measured in accor dance with ASTM E810. The reflective material shall be protected with an easily removable cover of heat resistant material capable of withstanding and protecting the reflective material from the application of asphalt at temperatures exceeding 325°F.
1015.09 RAISED PAVEMENT MARK ERS. Markers shall be either
non-reflectorized or reflectorized, as specified. Markers shall be from the Approved Materials List.
1015.09.1 Non-Reflectorized Markers:
1015.09.1 1 Description: Non-reflectorized markers shall
consist of an acrylonitrile butadiene styrene polymer or other approved material, and shall be approximately 4 x 6 -inches.
1015.09.1 2 Physical Requirements: Markers shall comply
with the compressive strength requirements of ASTM D4280. The color shall be in accordance with the plans and the MUTCD.
1015.09.2 Reflectorized Markers: Reflectorized markers shall
comply with ASTM D4280, Designation H and Designation F. The type and color shall be in accordance with the plans and the MUTCD. The markers shall be either standard having minim um base dimensions of 3 x 3 - inches and a maximum height of 0.80 inches or low profile having
1015.08 Temporary Pavement M Arkings.
1015.08.1 Temporary Tape: Temporary tape shall comply with
ASTM D4592, Type I (removable) or Type II (non -removable) an d shall be from the Approved Materials List.
1015.08.2 Painted Stripe: Paint shall be an approved traffic paint
complying with 1015.12 . Glass beads for drop -on applicati on shall comply with 1015.13.
1015.08.3 Temporary Raised Pavement Markings for Asphalt
Surface Treatment: Temporary raised pavement markers for asphalt surface treatment s hall be flexible reflective tabs having a nominal width of 4 inches. The markers shall be yellow with amber reflective area on both sides. The body of the marker shall consist of a base and vertical wall made of polyurethane or other approved material and shall be capable of maintaining a reasonable vertical position after installation. The initial minimum Coefficient of Luminous Intensity at an entrance angle of -4 degrees and an observation angle of 0.2 degrees shall be 230 mcd/lx when measured in accor dance with ASTM E810. The reflective material shall be protected with an easily removable cover of heat resistant material capable of withstanding and protecting the reflective material from the application of asphalt at temperatures exceeding 325°F.
1015.09 RAISED PAVEMENT MARK ERS. Markers shall be either
non-reflectorized or reflectorized, as specified. Markers shall be from the Approved Materials List.
1015.09.1 Non-Reflectorized Markers:
1015.09.1 1 Description: Non-reflectorized markers shall
consist of an acrylonitrile butadiene styrene polymer or other approved material, and shall be approximately 4 x 6 -inches.
1015.09.1 2 Physical Requirements: Markers shall comply
with the compressive strength requirements of ASTM D4280. The color shall be in accordance with the plans and the MUTCD.
1015.09.2 Reflectorized Markers: Reflectorized markers shall
comply with ASTM D4280, Designation H and Designation F. The type and color shall be in accordance with the plans and the MUTCD. The markers shall be either standard having minim um base dimensions of 3 x 3 - inches and a maximum height of 0.80 inches or low profile having
1015.08 Temporary Pavement M Arkings.
1015.08.1 Temporary Tape: Temporary tape shall comply with
ASTM D4592, Type I (removable) or Type II (non -removable) an d shall be from the Approved Materials List.
1015.08.2 Painted Stripe: Paint shall be an approved traffic paint
complying with 1015.12 . Glass beads for drop -on applicati on shall comply with 1015.13.
1015.08.3 Temporary Raised Pavement Markings for Asphalt
Surface Treatment: Temporary raised pavement markers for asphalt surface treatment s hall be flexible reflective tabs having a nominal width of 4 inches. The markers shall be yellow with amber reflective area on both sides. The body of the marker shall consist of a base and vertical wall made of polyurethane or other approved material and shall be capable of maintaining a reasonable vertical position after installation. The initial minimum Coefficient of Luminous Intensity at an entrance angle of -4 degrees and an observation angle of 0.2 degrees shall be 230 mcd/lx when measured in accor dance with ASTM E810. The reflective material shall be protected with an easily removable cover of heat resistant material capable of withstanding and protecting the reflective material from the application of asphalt at temperatures exceeding 325°F.
1015.09 RAISED PAVEMENT MARK ERS. Markers shall be either
non-reflectorized or reflectorized, as specified. Markers shall be from the Approved Materials List.
1015.09.1 Non-Reflectorized Markers:
1015.09.1 1 Description: Non-reflectorized markers shall
consist of an acrylonitrile butadiene styrene polymer or other approved material, and shall be approximately 4 x 6 -inches.
1015.09.1 2 Physical Requirements: Markers shall comply
with the compressive strength requirements of ASTM D4280. The color shall be in accordance with the plans and the MUTCD.
1015.09.2 Reflectorized Markers: Reflectorized markers shall
comply with ASTM D4280, Designation H and Designation F. The type and color shall be in accordance with the plans and the MUTCD. The markers shall be either standard having minim um base dimensions of 3 x 3 - inches and a maximum height of 0.80 inches or low profile having
1015.08 Temporary Pavement M Arkings.
1015.08.1 Temporary Tape: Temporary tape shall comply with
ASTM D4592, Type I (removable) or Type II (non -removable) an d shall be from the Approved Materials List.
1015.08.2 Painted Stripe: Paint shall be an approved traffic paint
complying with 1015.12 . Glass beads for drop -on applicati on shall comply with 1015.13.
1015.08.3 Temporary Raised Pavement Markings for Asphalt
Surface Treatment: Temporary raised pavement markers for asphalt surface treatment s hall be flexible reflective tabs having a nominal width of 4 inches. The markers shall be yellow with amber reflective area on both sides. The body of the marker shall consist of a base and vertical wall made of polyurethane or other approved material and shall be capable of maintaining a reasonable vertical position after installation. The initial minimum Coefficient of Luminous Intensity at an entrance angle of -4 degrees and an observation angle of 0.2 degrees shall be 230 mcd/lx when measured in accor dance with ASTM E810. The reflective material shall be protected with an easily removable cover of heat resistant material capable of withstanding and protecting the reflective material from the application of asphalt at temperatures exceeding 325°F.
1015.09 RAISED PAVEMENT MARK ERS. Markers shall be either
non-reflectorized or reflectorized, as specified. Markers shall be from the Approved Materials List.
1015.09.1 Non-Reflectorized Markers:
1015.09.1 1 Description: Non-reflectorized markers shall
consist of an acrylonitrile butadiene styrene polymer or other approved material, and shall be approximately 4 x 6 -inches.
1015.09.1 2 Physical Requirements: Markers shall comply
with the compressive strength requirements of ASTM D4280. The color shall be in accordance with the plans and the MUTCD.
1015.09.2 Reflectorized Markers: Reflectorized markers shall
comply with ASTM D4280, Designation H and Designation F. The type and color shall be in accordance with the plans and the MUTCD. The markers shall be either standard having minim um base dimensions of 3 x 3 - inches and a maximum height of 0.80 inches or low profile having