2524.01DESCRIPTION
Erect traffic signs and delineators according to the contract documents. 2524.02
MATERIALS.
A.
Signing Materials: Apply Section 4186.
B.
Wood Posts: Apply Section 4164.
C.
Class A Crushed Stone: Apply Article 4120.04.
D.
Concrete Footings: Apply the provisions of Section 2403.
2524.03CONSTRUCTION
Ensure all parts used in construction of traffic signs and delineators are able to withstand a wind load of 30 pounds per square foot on the sign surface. A.
Fabrication of Signs. 1.
Traffic Signs.
according to the standards established in the Standard Highway Signs, 2004 edition, and 2012 Supplement as published by the US DOT.
route markers, are classified into two groups, Types A and B, as indicated in the contract documents. 1) Type A Signs.
• Aluminum, galvanized steel, plywood sheets mounted on wood posts or perforated square steel tubing. • Sign face material fabricated from reflective sheeting. • Sign legends accomplished with either the direct or reverse silk screen process, with black nonreflective sheeting that is direct applied, or transparent film, as approved for use by the retro reflective sheeting manufacturer.
in the contract documents. 2) Type B Signs.
• Extruded aluminum highway sign panels mounted on either wood posts, perforated square steel tubing, or steel breakaway posts as specified in the contract documents.
Highway Signing
2524.03
• •
c.
Sign face material fabricated from reflective sheeting. Sign legends accomplished through use of reflectorized or nonreflectorized letters, numerals, symbols, and borders that are direct applied.
in the contract documents.
sign according to Article 1105.03. Each drawing is to be a scale drawing of the sign face, showing the size, arrangement, and spacing of all letters, numerals, symbols, and borders. Digital printing shall comply with the following: • Sign manufacturer shall be certified for digital printing by the retro reflective sheeting manufacturer. • All digital printing shall be done in a workmanlike manner and as recommended by the manufacturer of the retro reflective sheeting. • Appropriate manufacturer's recommended overlaminate films must be used in digital printing. Any noticeable deviation from the shades shall be cause for rejection of any sign. • Opaque or transparent inks shall be of the type and quality recommended by the manufacturer of the retro reflective sheeting. • A matched component system, recommended by the manufacturer shall be used in the digital printing process.
2.
Reference Location Signs.
• Green reflectorized sheeting on flat aluminum or galvanized steel sheets as for Type A signs. • Reflectorized white message applied directly to the face material. • Dimensions as specified in the contract documents.
delineators.
location sign according to Article 1105.03. Each drawing is to be a scale drawing of the sign face, showing the size, arrangement, and spacing of all letters, numerals, symbols, and borders.
3.
Route Markers, 6 Inch by 6 Inch. Comply with the following: • Reflectorized sheeting on flat aluminum or galvanized steel sheets as for Type A signs. • Details as specified in the contract documents.
4.
Delineators.
reflector, appropriately housed and contained on Materials I.M.
486.07
2524.03
B.
Highway Signing
Erection of Signs, Reference Location Signs, and 6 Inch by 6 Inch Route Markers. 1.
Type A and B Signs.
dimensions and details shown in the contract documents. Obtain the Engineer's approval for all deviations from the contract documents before starting the work.
field drilling holes as shown in the contract documents. All labor and equipment necessary for this modification is included in the price bid for the post and no separate payment will be made.
minimum embedment of 5.0 feet.
accurately both vertically and horizontally. Place backfill consisting of Class A crushed stone meeting the requirements of Article
4120.04into the post holes. Place material in layers no more than 6
inches in depth. Thoroughly compact each layer taking care to preserve the alignment of the posts.
documents, carefully drill or dig footing holes to the required size at the proper location. Spread the excavated earth within the right-ofway to blend uniformly with the existing surface to the Engineer's approval.
uncompacted material from the bottom of the hole. Some of the holes will be located in the bottoms of drainage ditches. In these cases conduct construction operations so that water will not enter excavated holes.
inch to 15 inch wrench to bed washers and shims, and to clean bolt threads. Loosen each bolt in turn and retighten in systematic order to the torque specified in the contract documents. For the fuse plate assembly, tighten fuse bolts to the torque specified in the contract documents.
in the contract documents. Ensure stub posts and reinforcing are properly aligned and secured, complying with Article 2405.03, H, 3. Cast the footing to the elevation shown in the contract documents. Rod the concrete in place to fill all the voids. Form the exposed portion of the footing as shown in the contract documents. Shape the cap of the footing so that drainage is away from the base plate of the post. Apply the provisions of Section 2403.
2403.03, N, 2, attach the post and adjust for correct alignment and
elevation. Remove all excess concrete from around the holes.
documents. Take necessary measures to prevent damage to sign faces. Repair (at no additional cost to the Contracting Authority) any mars, scratches, dents, or other damage to sign faces visible at a distance of 5 feet. Tighten locknuts on the post clip bolts by
Highway Signing
2524.03
means of a torque wrench to 225 inch-pounds when using dry, clean, unlubricated threads. Draw the nuts on panel bolts tight.
C.
2.
Delineators, Reference Location Signs, and 6 Inch by 6 Inch Route Markers.
inch by 6 inch route markers. Provide a suitable driving cap. Attach signs and delineators after driving.
reflectors will be at elevations called for in the contract documents. Ensure they are true to line and grade and are truly vertical. Where a reference locations sign is designated, attach the marker in place of a delineator. Where a 6 inch by 6 inch route marker is designated, attach it above the reference location sign on the same post.
ground, spaced as shown in the contract documents, and driven to the required lines and grades. Ensure that after driving, the top of the post has substantially the same cross section dimensions as the body of the post. Battered heads will not be permitted. Remove from the site and replace (at no additional cost to the Contracting Authority) all posts which are bent or otherwise damaged to the extent that they are, in the Engineer's opinion, unfit in the finished work.
3.
Perforated Square Steel Tube (PSST) Posts and Anchors.
impact from an errant vehicle.
concrete are free of concrete to allow drainage.
Sign Positioning. The glossy surface on sign faces may produce specular reflection. Position signs to eliminate or minimize specular reflection in the following manner: 1.
Overhead Signs.
approaching the sign is plus 2.0% or greater: • Vertical axis to be parallel to a plumb line. • Horizontal axis to be at right angles to the road.
approaching the sign is less than plus 2.0%: • Vertical axis inclined to face upward at the rate of 1/8 inch per foot of vertical sign surface for each 1% the road grade differs from plus 2.0%. • Horizontal axis to be at right angles with the road.
2524.04
Highway Signing
2.
D.
Ground Installations.
night by the Engineer. If specular reflection is apparent on any sign, adjust its positioning to eliminate or minimize this condition.
Sign Identification. Identify the signs as specified in Section 4186, with the following additions: Sign No................. (Filled in by Sign Fabricator) Erection Date........ (Filled in by Sign Contractor)
2524.04METHOD OF MEASUREMENT
Measurement for signing, satisfactorily erected according to the contract documents, will be as follows: A.
Type A Signs. 1.
Calculated in square feet of sign area completed in place based on the nominal dimensions of the signs.
2.
The area of all regular, rectangular, triangular, octagonal, and circular shaped Type A signs will be measured from the nominal given dimensions. Cutouts for rounded corners, and so forth, will not be deducted. The area of all irregularly shaped Type A signs, such as U.S. and Interstate route markers, will be measured from the dimensions of a circumscribed rectangle around the route marker.
B.
Type B Signs. Calculated in square feet on the basis of area of the vertical, front face of the signs specified in the contract documents. Measurement will not be made for area in excess of this area.
C.
Wood Posts for Type A or B Signs. Each to the nearest foot for the various post sizes installed. When posts are placed to depths greater than the minimum depth specified, the measured length does not include any parts placed to depths greater than 1 foot more than the specified minimum.
D.
Steel Breakaway Posts for Type A or B Signs.
E.
1.
Each to the nearest 0.1 foot for the various post sizes installed.
2.
Unless specified otherwise in the contract documents, the measured length of steel breakaway posts includes no more than 1 foot over the length necessary to meet specified minimums.
Concrete Footings for Breakaway Posts for Type A or B Signs. Each will be counted by the various sizes installed.
Highway Signing
F.
2524.05
Delineators, Reference Location Signs, and 6 Inch by 6 Inch Route Markers. Each will be counted by the various types installed.
Linear feet, to nearest foot, measured from top of anchor to top of post. Embedded length will not be measured separately, but included in price bid for Perforated Square Steel Tube Posts. H.
Perforated Square Steel Tube Post Anchors. By count of each type installed.
2524.05BASIS OF PAYMENT
Payment for signing, satisfactorily erected according to the contract documents, will be at the contract unit price as follows: A.
B.
C.
D.
Type A Signs. 1.
Per square foot of sign area.
2.
Payment is full compensation for furnishing, fabricating, and erecting the signs complete, including furnishing of the blank, application of reflective sheeting, application of the screened message, and all mounting hardware.
Type B Signs. 1.
Per square foot of sign area.
2.
Payment is full compensation for: • Furnishing, fabricating, and erecting the complete signs, including furnishing aluminum extrusions or formed steel panel, • Applying reflective sheeting, • Furnishing and applying all letters, numerals, symbols, and border to the sign • Applying the sign to the post, • Furnishing all labor, and • Furnishing all other details necessary to provide signs complete and erected in place, except for the required footings and posts.
Wood Posts for Type A or B Signs. 1.
Per linear foot.
2.
Payment is full compensation for furnishing and erecting the posts, including treatment and other details necessary to provide the sign posts complete and erected in place.
Steel Breakaway Posts for Type A or B Signs. 1.
Per linear foot for the various post sizes.
2524.05
Highway Signing
2.
E.
F.
Payment is full compensation for furnishing, fabricating, and erecting the posts, including galvanizing and other details necessary to provide the sign posts complete and erected in place.
Concrete Footings for Breakaway Posts for Type A or B Signs. 1.
Each for the various sizes.
2.
Payment is full compensation for: • Excavating the hole, • Furnishing and placing concrete, stub post, reinforcing bars, and so forth, • Finishing, and • All other details necessary to provide a complete concrete footing.
Delineators, Reference Location Signs, and 6 Inch by 6 Inch Route Markers. 1.
Delineators and Reference Location Signs:
• Furnishing, fabricating, and erecting the delineators or reference location sign complete, including posts, reflector units, and frames for delineators, posts and reference location signs, • Furnishing all necessary fittings and attachments, and • All labor necessary to complete the work.
2.
6 inch by 6 inch Route Markers:
route marker to a reference location sign post previously measured for payment, including all necessary fittings and attachments and all labor necessary to complete the work.
posts.
pavement, backfilling with concrete, slip base hardware, and other details necessary to provide anchor complete and erected in place.
Traffic Signalization
I.
2525.01
Excavation in Unexpected Rock. Excavation in unexpected rock for wood posts for Type A or B signs, steel posts for Type A or B signs, concrete footings for Type A or B signs, delineators, perforated square steel tube posts, and reference location signs will be paid for as extra work in Article 1109.03, B. Unexpected rock will be considered as rock encountered during post erection, but neither visible from the roadway nor indicated in the contract documents.