KDOT 404: Concrete for Prestressed Concrete Members

– CONCRETE FOR PRESTR ESSED CONCRETE MEMBERS CONCRETE FOR PRESTRESSED CONCRETE MEMBERS

404.1DESCRIPTION

Provide concrete with the release and 28 day compre ssive strengths specified in the Contract Documents. This specification is specific to Concrete for Prestressed Concrete Members. See SECTION 401 for general concrete requirements.

404.2MATERIALS

Provide materials that comply w ith the applicable requirements. General Concrete .................................................................................................... … SECTION 401 Aggregate ............................................................................................................... ….. DIVISION 1100 Admixtures and Plasticizers .................................................................................. ….. DIVISION 1400 Grade 2 Calcium Chloride ...................................................................................... ….. DIVISION 1700 Cement, Fly Ash, Silica Fume, Slag Cement and Blended Supplemental Cementitious........................................................................................................... …. DIVISION 2000 Water ………………………………………………………………. ..................... ….. DIVISION 2400

404.3CONCRETE MIX DESIGN

a.General. Design concrete mixes specified in the Contract Documents. A mix design must be approved

by the Engineer before the mix can be used in the production of prestressed concrete members.

b.Concrete Mix Design. Two options are available for mix desi gn procedures. Use the procedures

outlined in SECTION 401, or use TABLE 404-2 to design structural concrete mixes.

c.Concrete Strength Requirements. Unless shown otherwise in the Contract Documents, design

concrete to meet the compressive strength requirements of TABLE 404-1 . For prestressed bridge beams, the Engineer will determine the strength requirements from the table except when specified elsewhere in the Contract Documents. TABLE 404-1: COMPRESSIVE STRENGTH REQUIREMENTS Type of Unit For Stress Application

(Release)and/or moving*

(Minimum)(psi)

Age 28 Days (Minimum)** (psi) Prestressed Bridge Beams 5800 7000 4800 6000 4000 5000 Prestressed Piles 3000 5000 Prestressed Panels 4000 5000 * From casting bed to producer’s storage only. Not a shipping strength. ** Also required for shipping strength.

d.Portland Cement, Blended Hydraulic C ement and Individual and Blended Supplemental

Cementitious Materials. Unless specified otherwise in the Contract Documents, select the type of portland cement, blended hydraulic cement and indi vidual and blended supplemental cementitious materials according to SECTION 401. – CONCRETE FOR PRESTR ESSED CONCRETE MEMBERS

e.Specific Requirements for Concrete used in Prestressed Concrete Members. Design concrete to

meet the requirements of TABLE 404-2. TABLE 404-2: CONCRETE REQUIREMENTS Self-Consolidating Concrete (SCC) Non SCC All Concrete Slump Flow From Target (Inches) Blocking Assessment (Inches) Visual Stability Index Maximum Slump (Inches) Minimum Cementitious per Cubic Yard (Lbs) Mixing Water: Maximum lb. per lb. Cementitious Air Content (%) ± 2 2 maximum 0 or 1 5 or 7 ± 25% 602 0.44 6.5 ± 1.5

(1)Determine the slump flow using ASTM C 1611, “Standard Test Method for Slump Flow of Self-

Consolidating Concrete.” The target value is determined during the mix design and approval process (see below). At the point of placement, slump flow can deviate from target by no more than 2 inches.

(2)Determine the blocking assessment using ASTM C 1621, “Standard Test Method for Passing Ability of

Self-Consolidating Concrete by J-Ring.”

(3)Determine the visual stability index (VSI) using Appendix X1 of ASTM C 1611. When approved by

the Engineer, the VSI may be determined using additional concrete stability observations.

(4)Designate a slump for each concre te mix design that is no greater than 5 inches when not using mid-

range or high-range water reducing admixtures. When a water reducing admixture is being used, designate a slump no greater than 7 inches. The tolerance from design at the point of delivery is ± 25%.

(5)It may be necessary to adjust the mix proportions, as permitted by the specifications, to provide a mix

that complies with placement, and the release and 28-day strength requirements.

(6)Maximum limit of lb. of water per lb. of cementitious material includes free water in aggregates, but

excludes water of absorption of the aggregates.

(7)Non-air entrained concrete may be used in co ncrete piling not subject to freezing and thawing and

wetting and drying.

(8)There are no permeability requirements.

(9)Determine air content by KT-19 (Volumetric Me thod). A regularly calibrated KT-18 (Pressure

Method) meter may be used for production with random verification by the Volumetric Method. See KT-19 for special requirements when using the Volumetric Method with high cemen titious concretes or mixtures with midrange water reducers or plasticizers.

(10)Use Quality Requirements for St ructural Aggregates as listed in SECTION 1102 , Aggregates For

Concrete Not Placed on Grade. Keep a copy of the KDOT O fficial Quality test report from the approved source on file at the prestress plant and available for review by the Engineer.

(11)Use gradation requirements for aggregates as listed in SECTION 1102, Aggregates For Concrete Not

Placed on Grade.

(12)When used, add silica fume with other cementitious materials during batching procedures. If the silica

fume cannot be added to the cementitious materials, add th e loose silica fume to the bo ttom of the stationary drum that is wet, but has no standing water, before adding the dry materials. The Engineer may approve shreddable bags on a performance basis, only when a central batch mixing process is used. If so, add the bags to half of the mixing water and mix before adding cementitious materials, aggregate and remainder of water. The presence of visible chunks or wads of bag paper at the point of placement will be cause for rejection. Mix silica fume modified concrete for a minimum of 100 mixing revolutions, unless high speed mixing equipment is used.

(13)ASTM C-1567 is required if supplementar y cementitious materials (SCMs) are utilized. See

subsection 401.3d.(6) for requirements. ASTM C 1567 is not necessary for concrete modified with only Silica Fume.

(14)For the approved source of water, keep a copy of the KDOT test report on file at the prestress plant and

available for review by the Engineer.

(15)Use admixtures that are prequalified. Maintain a copy of the Type C certification on file at the prestress

plant and available for review by the Engineer. No other additives may be used without written approval by the Engineer. – CONCRETE FOR PRESTR ESSED CONCRETE MEMBERS

f.Additional Design Requirements for Self-Consolidating Concrete (SCC). SCC is defined as a concrete

mixture which can be placed by means of its own weight with little to no vibration. It is accomplished by adjusting traditional mix designs using special admixtures.

(1)Do not rod or vibrate when making test cylinders.

(2)Provide scales capable of determining test block weights for the strand bond test that are calibrated (NIST

traceable) and approved by the Engineer.

(3)Perform a strand bond test (KT-83) for each mix a nd strand to be used in the future production of

prestressed beams. Any change in admixture, aggregate source or gradation, cementitious material content or source, and strand producer or size requires that a new strand bond test be completed using the replacement materials. Make 2 test beams for each bond test. Cure the test beams in an environment that is representative of future production (i.e. – moisture and heat until release then ambient conditions).

(a)With the Engineer observing, perform a single Sl ump Flow test for each pair of test beams cast.

This spread establishes a target value from whic h future point of placement values are to be compared to. Assign a Visual Stability Index (VSI) number to the concrete spread.

(b)With the Engineer observing, perform a single J-Ring test for each pair of test beams cast.

Calculate a “blocking assessment” value.

(c)Make a minimum of 2 sets of 3 cylinders for each pair of test beams cast. Cure the cylinders with

the test beams they represent.

(i)With the Engineer observing, test 1 set of cylinders at the producer’s plant to measure for

release (equal to the release strength of future production). De-tension the strand in both test beams only after this cylinder set indicates that release strength has been attained.

(ii)With the Engineer observing, test 1 set of cylinders at the producer’s plant to measure for

28-day strength (equal to the 28-day strength of future production). Perform the bond test on both test beams only after this cylinder set indicates that the 28-day strength has been attained.

(iii)In both cases, the required strength is met when the average compressive strength of the 3

cylinders equals or exceeds the required strength, and no more than 1 cylinder in the tested set had a strength that was no more than 5% below the required strength.

(d)With the Engineer observing, measure the dimensions of both test beams to verify the required

casting tolerances. Calculate the weight of the required test loads.

(e)With the Engineer observing, load the test beams using the calculated loads and KT-83.

(f)Submit all beam dimensions, calculations (intermediate and final), release and 28-day strengths,

observations, measurements, pictures, and test results related to strand bond, cylinder strength, slump flow, and J-ring testing to the Engineer for review.

(g)In addition to the requirements of this section and SECTION 401, the mix design represented by

this testing may be approved provided there are 2 passing bond tests, and the assigned blocking assessment and the calculated VSI satisfy the requirements of TABLE 404-2.

Sections that cite this one

107Legal Relations and Responsibility to The Public

Get an email when 404 changes

Kansas revises spec sections through supplementals and new editions. We check this one every week and email you the day it changes. Free, no account.

Source: Standard Specifications for State Road and Bridge Construction, 2015 Edition. Pages 191–193 of 978. View official source ↗

← Previous

403 On Grade Concrete

405 Curing Environment

404Concrete for Prestressed Concrete Members

Ask about Section 404