806Durable Pavement Marking

- DURABLE PAVEMENT MARKING DURABLE PAVEMENT MARKING

806.1DESCRIPTION

Prepare the pavement and apply the pavement markings as shown in the Contract Documents. When rumble strips are to be constructed on the pr oject, construct the centerline rumble strips before installing centerline pavement marking. B I D I T E M S U N I T S Pavement Marking (*) (**) (***) (*****) Linear Foot Pavement Marking Symbol (*) (White) (****) (*****) Each *Type of Pavement Marking: Cold Pl astic, Patterned Cold Plastic, Epoxy, Thermoplastic, Preformed Thermoplastic, Thermoplastic-Spray, Intersection Grade, High Durability or Multi-Component ** Color *** Width **** Type of Symbol ***** Contrast

806.2MATERIALS

Provide durable pavement marking materials that comply with DIVISION 2200.

806.3CONSTRUCTION REQUIREMENTS

pavement marking material.

Safety Services Association (ATSSA) pavement marking certification and experienced in the application of the appropriate type of pavement marking material.

manufacturer indicating the Contractor’s qualifications to install their product.

complete a 300-foot test section for epoxy, thermoplastic, sprayed thermoplastic and multi-component pavement markings that meet the requirements of this specification. The Engineer will inspect the test strip 24 hours after it has been placed. Do not begin pavement marking operations, until the Engineer approves the test strip.

(removed and paid for under SECTION 808) and according to the recommendations of the manufacturer of the new pavement markings. Remove temporary pavement markings, if any, the same day the durable pavement markings are applied. Removal of temporary pavement marking is subsidiary to temporary pavement marking bid items. Remove loose particles, dirt, tar, grease, residue of prior pavement markings and other deleterious material from the pavement surfaces.

Documents do not provide details, submit to the Engineer for approval, a layout plan for the pavement markings that complies to the MUTCD. Locate longitudinal pavement marking stripes a minimum of 2 inches and a maximum of 8 inches from longitudinal joints. Provide adequate guide marks (approximately 2 inches by 12 inches at approximately 30 to 50-foot intervals) for the application of the pavement markings. When applying pavement markings at locations with newly constructed rumble strips, use the same guide marks that were used for milling the rumble strips, or when approved by the Engineer, establish a new guide mark, if the guide mark used with the rumble strips is not visible enough to follow.

¼ inch above the specified plan width. See TABLE 806-3 for minimum pavement marking widths. - DURABLE PAVEMENT MARKING

instructions. Apply the pavement markings according to the manufacturer’s recommendations. Follow the manufacturer’s recommendations regarding pavement and ambient temperature at the time of application. The Engineer will verify the pavement and ambient temperatures before beginning work and when deemed necessary. Apply pavement markings straight and close to the intended alignment without abrupt changes that result in an unacceptable appearance. Meet the minimum retroreflectivity requirements in TABLE 806-1.

the Contract Documents.

• have drag marks, gashes, gouges, foreign covering, discolored areas or areas that have failed to solidify. • have improper adhesion, length or thickness. • have areas that present a ragged appearance, ar eas that do not present sharply defined edges, or areas with abrupt unintended changes in alignment.

feet may be rejected.

spaced every 1 mile. Remove and replace the defici ent widths of pavement markings so the total length of deficiency in any 1 mile section is less than 300 feet.

marking. TABLE 806-1: MINIMUM RETROREFLECTIVITY REQUIREMENTS Type of Material Color millicandelas/sq m/lux*

Cold Plastic White 250 Yellow 175 Patterned Cold Plastic White 500 Yellow 300 Epoxy or Multi-Component White 325 Yellow 250 High Durability Tape White 225 Yellow 175 Thermoplastic, Preformed Thermoplastic or Spray Thermoplastic White 300 Yellow 225 NOTE: Provide an acceptable 100-foot retroreflectometer to use on the project which will remain the property of the Contractor. In the presence of the Engineer, measure the retroreflectivity between 12 hours and 14 days afte r the application of all pavement markings. Take a minimum of 5 randomly spaced readings per color line every 1 mile. The Engineer will average all of the readings for each color line within the 1 mile section to determine the retroreflectivity. - DURABLE PAVEMENT MARKING If the pavement markings have a retror eflectivity reading as measured for TABLE 806-1 (in any 1 mile section) less than that shown in TABLE 806-2, remove and replace the entire 1 mile section. TABLE 806-2: RETROREFLECTIVITY READINGS REQUIRING REMOVAL OF PAVEMENT MARKING Type of Material Color Retroreflectivity reading (R) in a 1 mile section (millicandelas) Cold Plastic White 200 Yellow 125 Patterned Cold Plastic White 450 Yellow 250 Epoxy or Multi-Component White 275 Yellow 200 High Durability Tape White 175 Yellow 125 Thermoplastic, Preformed Thermoplastic or Spray Thermoplastic White 250 Yellow 175

acceptance until the pavement markings complete a 180 cal endar day observation period. The Contractor is responsible for the pavement marking during this period. The 180 calendar day observation period begins the day following the completion of the pavement marking. Providing all other work on the contract is complete, the Engineer will not assess working day charges during the 180 calendar day observation period. Immediately following the 180 day observation period, arrange with the Engineer to have a joint meeting to examine the pavement marking. The Engineer will provide written results of the final examination to the Contractor within 5 business days of the joint meeting. Before the project is accepted, replace all failed pavement markings, at own expense. The pavement marking is failed, when more than 10% of the substrate is exposed in a 2,000-foot section of longitudinal pavement marking line. The transverse lines and symbols will be evaluated separately for the exposure of 10% substrate. Abrasion of pavement marking at private entrances or intersections may be excluded from examination. If the Contractor fails to complete the required replacement of pavement markings within 10 business days of the date of the notice of the unacceptable pavement markings, during which the application of pavement markings is not precluded by adverse weather or road surface conditions, the Engineer, after giving the Contractor written notice, will reinstate the assessment of working day charges or Liquidated Damages. Working day charges or Liquidated Damages will continue until the work is accepted. If more than 30% of pavement marking is required to be replaced, the replacement pavement markings will not be accepted until the completion of an additional 180 calendar day observation period. The Engineer will, upon sati sfactory inspection of the pavement marking, accept the work and terminate the Contractor’s responsibilities.

into the surface of the pavement. Grind the inset 0.08 inches (+ 0.01 inch tolerance) deep, with the width and length of the inset a maximum of 2 inches greater than the dimensions of the pavement marking. On new or existing PCCP, cut the marking tape at any joint in the pavement that is crossed by the tape. Apply adhesive-sealer primer of a type recommended by the manufacturer. Primer is required on all tape applications regardless of temperature, date or season.

bridge decks) less than 1 year old, remove all curing compounds and laitance by shot, sand or waterblasting. Use a slower curing epoxy material (40 minutes) for pavement markings applied to PCCP. For other surfaces, fast setting (10 minutes) epoxy material may be used with approval of the Engineer. Apply the epoxy liquid material closely behind the surface cleaning procedures. - DURABLE PAVEMENT MARKING Before mixing the components of the pavement marking material, heat the individual components to the temperature ranges recommended by the manufacturer of the material. Do not excee d the maximum recommended temperature at any time. Apply the epoxy liquid pavement marking material at a thickness of 20-25 mils on all pavement. Immediately apply all glass beads (double drop system or blended bead) to the epoxy liquid pavement marking at the glass bead gradation and bead drop rate recommended by the manufacturer to obtain the required level of retroreflectivity.

(including concrete bridge decks) less than 1 year old, remove all curing compounds and laitance by shot, sand or waterblasting. For intersection grade multi-component, grind the inset 15 mil (+10 mil tolerance) deep, with the width and length of the inset a maximum of 2 inches greater than the dimensions of the pavement marking on concrete surfaces. Multi-component liquid pavement marking will only be allowed for use on concrete pavement on a pre- qualified basis. Apply the multi-component liqui d material closely behind the surface cleaning procedures. Before mixing the components of the pavement marking material, heat the individual components to the temperature ranges recommended by the manufacturer of the material. Do not excee d the maximum recommended temperature at any time. Apply the multi-component liquid pa vement marking material at the thickness of 20-25 mils on all pavement. Immediately apply the glass beads (double drop system or blended drop) to the multi-component liquid pavement marking at the glass bead gradation and bead drop rate recommended by the manufacturer to obtain the required level of retroreflectivity.

Grind the inset 80 mil (+10 mil tolerance) deep with the width and length of the inset a maximum of 2 inches greater than the dimensions of the pavement marking. Apply adhesive-sealer primer of a type recommended by the manufacturer. Primer is required on all tape applications regardless of temperature, date or season. On new or existing PCCP, cut the marking tape on either side of any joint in the pavement that is crossed by the tape.

the inset a maximum of 2 inches greater than the dimensions of the pavement marking on concrete surfaces. Use a heating device recommended by the material manufacturer to fuse the preformed thermoplastic to the pavement. Apply adhesive-sealer primer of a type recommended by the manufacturer. Primer is required on all preformed applications on concrete regardless of temperature, date or season. Apply the pavement markings as recommended by the manufacturer.

pavement marking. Thickness will be checked by placing metal plates or other suitable material of known thickness in a 3-foot section along the path of application at 2 to 3 locations. After the application of the thermoplastic material, the samples will be cut free. The material thic kness will be measured using either a micrometer or vernier calipers (with proper correctio n for the metal plate). The thickness reco rded for the locations within the 3-foot section will be averaged. Initially, thic kness determinations will be made every ⅓ mile for each color and each stripe width. Once a pattern of compliance is established, the Engineer may reduce the frequency of thickness verification to once each 1 mile section. Failure of a section will require testing to return to the initial frequency until compliance may be re-established. The location of the 3-foot sample segment within the sample section will be selected at random. The Contractor may provide other devices for gauging thickness to the Engineer for approval. Apply thermoplastic pavement markings between April 15 and October 15. If the manufacturer’s recommendations allow, the Engineer may waive the date re strictions. The Engineer will notify the Contractor in writing of any allowed variance.

90 mil at the edges, and a maximum of 125 mil at the cente r of the stripe. The required thickness for transverse markings and symbols is a minimum of 90 mil at the edges, and a maximum of 140 mil at the center. - DURABLE PAVEMENT MARKING For transverse markings on concrete, grind the inse t 40 mil (+20 mil tolerance) deep, with the width and length of the inset a maximum of 2 inches greater than the dimensions of the pavement marking on concrete surfaces. Apply the binder-sealer according to the manufacturer ’s recommendations. Primer is required on all transverse applications on concrete regardless of temperature, date or season. The Engineer will not approve the application of the thermoplastic material until the binder-sealer applied to the pavement is devoid of all solvent or water. Apply prepared thermoplastic material in a molten stat e within a temperature range of 400 to 440ºF. The Engineer will not approve the use of scorched material or prepared material that has been maintained at 440ºF for a period exceeding 4 hours. Apply glass beads (double drop system or blended bead) to the thermoplastic pavement marking at the glass bead gradation and bead drop rate recommended by the manufacturer to obtain the required level of retroreflectivity.

intermittent markings on concrete or asphalt surfaces . The trailing (black) pavement marking shall be placed concurrently to the white pavement marking line when applied to the roadway. Apply black, opaque coal slag (20-40 mixture) to the trailing pavement marking line at a rate of 8-10 pounds per gallon of liquid pavement marking to achieve a skid resistance value of 50 BPN. Apply leading/trailing pavement markings that follow the same space conf iguration as broken lines, dotted extension and lane drop markings in the Contract Documents.

806.4MEASUREMENT AND PAYMENT

The Engineer will measure the various widths and colors or pavement markings by the linear foot. When the Contract Documents specify that the contrast pavement markings are installed in a leading/trailing configuration, the Engineer will measure the black pavement marking and white pavement marking separately by the linear foot. The Engineer will measure each symbol. The Engineer will pay for 90% of the completed quantity for each of th e various widths and colors of pavement marking and symbols. Upon acceptance of the pavement markings following the 180 day observation period, the Engineer will pay for the remaining 10% of the completed quantity for each of the various widths and colors of pavement marking and symbols. When necessary, removal of permanent pavement markings will be measured and paid for under Payment for "Pavement Marking" an d "Pavement Marking Symbol" at th e contract unit prices is full compensation for the specified work. Pay adjustments for width and retr oreflectivity deficiencies (see TABLES 806-3 and 4) will be entered on the Contractor’s Payment Vouchers (intermediate and final) under the bid item Contract Deduct. TABLE 806-3: DURABLE PAVEMENT MARKING WIDTH DEFICIENCY DEDUCTION (Epoxy, Thermoplastic, Spray Thermoplastic and Multi-Component) Specified Width (inches) Actual Width (inches) Distance (D) the width is deficient in any 1 mile section Deduction 4 3 ¾ to 4 D ≤ 50 No deduction. 4 3 ¾ to 4 50 < D < 300 20% deduction of the contract line item for the entire 1 mile section. 6 5 ¾ to 6 D ≤ 50 No deduction. 6 5 ¾ to 6 50 < D < 300 20% deduction of the contract line item for the entire 1 mile section. - DURABLE PAVEMENT MARKING TABLE 806-4: DURABLE PAVEMENT MARKING RETROREFLECTIVITY DEDUCTION* Type of Material Color Retroreflectivity reading

(millicandelas) Deduction of the contract line item for the entire 1 mile section Cold Plastic White 225 ≤ R < 250 15% 200 ≤ R < 225 25% Yellow 150 ≤ R < 175 15% 125 ≤ R < 150 25% Patterned Cold Plastic White 475 ≤ R < 500 15% 450 ≤ R < 475 25% Yellow 275 ≤ R < 300 15% 250 ≤ R < 275 25% Epoxy or Multi-Component White 300 ≤ R < 325 15% 275 ≤ R < 300 25% Yellow 225 ≤ R < 250 15% 200 ≤ R < 225 25% High Durability Tape White 200 ≤ R < 225 15% 175 ≤ R < 200 25% Yellow 150 ≤ R < 175 15% 125 ≤ R < 150 25% Thermoplastic, Preformed Thermoplastic or Spray Thermoplastic White 275 ≤ R < 300 15% 250 ≤ R < 275 25% Yellow 200 ≤ R < 225 15% 175 ≤ R < 200 25% *Retroreflectivity readings used for calculating the deduction will be taken from reading required in TABLE 806-1.