Santa Ana, California Building Permit Cost Calculator
Estimates permit cost in Santa Ana from the city's own published fee schedule — not a national average. Every figure is computed from a rule quoted verbatim from that document, and rules that cannot be computed honestly are shown as the published text instead of a number.
217 jurisdictions with fee schedules on file
Total cost of work, labor and materials
Used by cities that price per square foot
Fences and retaining walls
Electrical permits priced by the ampere
Building Permit
These lines are alternatives, not a running bill. Pick the one that describes your project and any percentage-based add-ons will be calculated from it.
○2,500 sf residential 2-story SFD, structural plan check, per sq ft Flat fee $3.14 | $3.14 |
○Same, if single story, per sq ft Flat fee $1.42 | $1.42 |
○Same, if repeat, per sq ft Flat fee $0.73 | $0.73 |
○2,500 sf residential SFD, structural inspection, per sq ft Flat fee $0.81 | $0.81 |
○Permit issuance fee, residential and non-residential Flat fee $194.30 | $194.30 |
○Minimum fee, inspection (flat) Flat fee $212.11 | $212.11 |
○Minimum fee, plan check (hourly, min. 1/2 hour) Flat fee $294.06 | $294.06 |
How this jurisdiction calculates the fee
Santa Ana prices building permits from the FY 2025-26 Adopted Miscellaneous Fees Schedule (Section IX/X, Planning & Building Agency) rather than from an ICC valuation multiplier. Structural plan check and structural inspection are charged as separate per-square-foot rates that step down as the project gets larger, and electrical, mechanical and plumbing ("EMP") are billed separately from their own itemized per-device schedules rather than being bundled. Residential single-family rates differ by whether the plan is two-story, single-story, or a repeat of an already-approved plan. There is a flat permit issuance fee, a higher one for residential and non-residential building permits than for EMP and miscellaneous permits, plus a flat General Plan Update surcharge on each permit. Minimum plan check is billed hourly with a half-hour floor. SUPERSESSION 2026-09-10: this row cited the FY 2025-26 Adopted Miscellaneous Fees Schedule, whose document URL still returns HTTP 200 but is no longer the schedule the city lists as current. The FY 2026-27 Miscellaneous Fees Schedule was ADOPTED JUNE 2, 2026 and took EFFECT JULY 1, 2026 under Fees Resolution 2026-028, and raised essentially every Building Division amount by about 4 percent. Reference points: permit issuance residential/non-residential $186.83 to $194.30, permit issuance EMP and misc. building $70.06 to $72.86, minimum inspection fee $203.95 to $212.11, minimum plan check $282.75 to $294.06, minimum fee nonresidential $93.40 to $97.14, and the General Plan Update surcharge $28.10 to $29.22. The percentage-based charges (electrical, mechanical and plumbing plan check at 65 percent of subtotal) did not change. All figures below are from the FY 2026-27 adopted edition.
Source: published fee schedule · Verified 11/6/2026
Deck Permit
These lines are alternatives, not a running bill. Pick the one that describes your project and any percentage-based add-ons will be calculated from it.
○Misc. residential structure, patio cover/garage, structural plan check, per sq ft Flat fee $0.53 | $0.53 |
○Misc. residential structure, patio cover/garage, structural inspection, per sq ft Flat fee $0.54 | $0.54 |
○Minimum fee, inspection (flat) Flat fee $212.11 | $212.11 |
○Minimum fee, plan check (hourly, min. 1/2 hour) Flat fee $294.06 | $294.06 |
○Permit issuance fee, residential and non-residential Flat fee $194.30 | $194.30 |
How this jurisdiction calculates the fee
Santa Ana publishes no line item named "deck." A permitted residential deck is priced under the closest published category, item 41/42, Miscellaneous Residential Structure: Patio Cover/Garage, which charges a structural plan check rate per square foot and a structural inspection rate per square foot, with EMP inspection billed separately from the individual item schedule if the deck has lighting or outlets. Add the flat permit issuance fee and the General Plan Update surcharge, and apply the published minimum inspection and minimum plan check floors, which will govern on a small deck. FY 2025-26 adopted schedule. SUPERSESSION 2026-09-10: this row cited the FY 2025-26 Adopted Miscellaneous Fees Schedule, whose document URL still returns HTTP 200 but is no longer the schedule the city lists as current. The FY 2026-27 Miscellaneous Fees Schedule was ADOPTED JUNE 2, 2026 and took EFFECT JULY 1, 2026 under Fees Resolution 2026-028, and raised essentially every Building Division amount by about 4 percent. Reference points: permit issuance residential/non-residential $186.83 to $194.30, permit issuance EMP and misc. building $70.06 to $72.86, minimum inspection fee $203.95 to $212.11, minimum plan check $282.75 to $294.06, minimum fee nonresidential $93.40 to $97.14, and the General Plan Update surcharge $28.10 to $29.22. The percentage-based charges (electrical, mechanical and plumbing plan check at 65 percent of subtotal) did not change. All figures below are from the FY 2026-27 adopted edition.
Source: published fee schedule · Verified 11/6/2026
Electrical Permit
These lines are alternatives, not a running bill. Pick the one that describes your project and any percentage-based add-ons will be calculated from it.
○Electrical permit issuance Flat fee $72.86 | $72.86 |
○Minimum fee (nonresidential) Flat fee $97.14 | $97.14 |
○Service/subpanel/meter change, under 400 amperes Flat fee $70.52 | $70.52 |
○Service change, 400 to 1,199 amperes Flat fee $192.29 | $192.29 |
○Air conditioners, heat pumps, each Flat fee $128.25 | $128.25 |
Electrical plan check fee (when required) · add-on 65% of subtotal — select the permit fee line above to calculate | see rule |
How this jurisdiction calculates the fee
Santa Ana is a true per-device electrical city. The FY 2025-26 schedule charges a flat electrical permit issuance fee and then itemizes each device: receptacle outlets, switches, light fixtures, dedicated circuits, air conditioners and heat pumps, and service or subpanel changes priced in amperage tiers, plus power equipment such as motors, transformers, water heaters and photovoltaic panels priced in HP/kW/kVA tiers. When electrical plans are required by the Building Official, an electrical plan check fee is added at 65 percent of the electrical permit subtotal. A nonresidential minimum fee floors the permit. SUPERSESSION 2026-09-10: this row cited the FY 2025-26 Adopted Miscellaneous Fees Schedule, whose document URL still returns HTTP 200 but is no longer the schedule the city lists as current. The FY 2026-27 Miscellaneous Fees Schedule was ADOPTED JUNE 2, 2026 and took EFFECT JULY 1, 2026 under Fees Resolution 2026-028, and raised essentially every Building Division amount by about 4 percent. Reference points: permit issuance residential/non-residential $186.83 to $194.30, permit issuance EMP and misc. building $70.06 to $72.86, minimum inspection fee $203.95 to $212.11, minimum plan check $282.75 to $294.06, minimum fee nonresidential $93.40 to $97.14, and the General Plan Update surcharge $28.10 to $29.22. The percentage-based charges (electrical, mechanical and plumbing plan check at 65 percent of subtotal) did not change. All figures below are from the FY 2026-27 adopted edition.
Source: published fee schedule · Verified 11/6/2026
Fence Permit
These lines are alternatives, not a running bill. Pick the one that describes your project and any percentage-based add-ons will be calculated from it.
○Fence (wood), 20 lf, structural plan check, per linear foot Flat fee $0.53 | $0.53 |
○Fence (wood), 20 lf, structural inspection, per linear foot Flat fee $0.38 | $0.38 |
○Minimum fee, inspection (flat) Flat fee $212.11 | $212.11 |
○Minimum fee, plan check (hourly, min. 1/2 hour) Flat fee $294.06 | $294.06 |
○Permit issuance fee, EMP and misc. building Flat fee $72.86 | $72.86 |
How this jurisdiction calculates the fee
Fences are billed per linear foot in items 62 and 63 of the FY 2025-26 schedule, with a structural plan check rate per linear foot and a structural inspection rate per linear foot, benchmarked in the schedule against a 20-linear-foot example. Because those linear rates are very low, the published minimum plan check and minimum inspection fees govern almost every residential fence permit. Add the flat EMP and miscellaneous building permit issuance fee and the General Plan Update surcharge. SUPERSESSION 2026-09-10: this row cited the FY 2025-26 Adopted Miscellaneous Fees Schedule, whose document URL still returns HTTP 200 but is no longer the schedule the city lists as current. The FY 2026-27 Miscellaneous Fees Schedule was ADOPTED JUNE 2, 2026 and took EFFECT JULY 1, 2026 under Fees Resolution 2026-028, and raised essentially every Building Division amount by about 4 percent. Reference points: permit issuance residential/non-residential $186.83 to $194.30, permit issuance EMP and misc. building $70.06 to $72.86, minimum inspection fee $203.95 to $212.11, minimum plan check $282.75 to $294.06, minimum fee nonresidential $93.40 to $97.14, and the General Plan Update surcharge $28.10 to $29.22. The percentage-based charges (electrical, mechanical and plumbing plan check at 65 percent of subtotal) did not change. All figures below are from the FY 2026-27 adopted edition.
Source: published fee schedule · Verified 11/6/2026
Reroof Permit
These lines are alternatives, not a running bill. Pick the one that describes your project and any percentage-based add-ons will be calculated from it.
○Residential re-roof, structural plan check, hourly Flat fee $294.06 | $294.06 |
○Residential re-roof, structural inspection, hourly Flat fee $212.11 | $212.11 |
○Commercial re-roof, structural plan check, hourly Flat fee $294.06 | $294.06 |
○Commercial re-roof, structural inspection, hourly Flat fee $212.11 | $212.11 |
○Permit issuance fee, EMP and misc. building Flat fee $72.86 | $72.86 |
○Permit issuance fee, General Plan Update surcharge Flat fee $29.22 | $29.22 |
How this jurisdiction calculates the fee
Unusually, Santa Ana prices reroofing entirely on an hourly basis rather than as a flat fee or from valuation. Items 92 through 95 set an hourly structural plan check rate and an hourly structural inspection rate, identical for residential and commercial. Because plan check is only triggered when the material or existing structure requires calculations, a routine residential reroof is effectively the minimum inspection fee plus the flat EMP and miscellaneous building permit issuance fee and the General Plan Update surcharge. FY 2025-26 adopted schedule. SUPERSESSION 2026-09-10: this row cited the FY 2025-26 Adopted Miscellaneous Fees Schedule, whose document URL still returns HTTP 200 but is no longer the schedule the city lists as current. The FY 2026-27 Miscellaneous Fees Schedule was ADOPTED JUNE 2, 2026 and took EFFECT JULY 1, 2026 under Fees Resolution 2026-028, and raised essentially every Building Division amount by about 4 percent. Reference points: permit issuance residential/non-residential $186.83 to $194.30, permit issuance EMP and misc. building $70.06 to $72.86, minimum inspection fee $203.95 to $212.11, minimum plan check $282.75 to $294.06, minimum fee nonresidential $93.40 to $97.14, and the General Plan Update surcharge $28.10 to $29.22. The percentage-based charges (electrical, mechanical and plumbing plan check at 65 percent of subtotal) did not change. All figures below are from the FY 2026-27 adopted edition.
Source: published fee schedule · Verified 11/6/2026
Retaining Wall Permit
These lines are alternatives, not a running bill. Pick the one that describes your project and any percentage-based add-ons will be calculated from it.
○Retaining wall, 20 lf, structural plan check, per linear foot Flat fee $0.54 | $0.54 |
○Retaining wall, 20 lf, structural inspection, per linear foot Flat fee $0.53 | $0.53 |
○Minimum fee, plan check (hourly, min. 1/2 hour) Flat fee $294.06 | $294.06 |
○Minimum fee, inspection (flat) Flat fee $212.11 | $212.11 |
○Permit issuance fee, residential and non-residential Flat fee $194.30 | $194.30 |
How this jurisdiction calculates the fee
Retaining walls are billed per linear foot in items 64 and 65, with a structural plan check rate per linear foot and a structural inspection rate per linear foot, benchmarked against a 20-linear-foot wall. As with fences, the linear rates are small enough that the published minimum plan check and minimum inspection fees govern typical residential walls. The flat permit issuance fee and the General Plan Update surcharge apply, and engineered walls that need calculation review are billed at the hourly plan check rate. FY 2025-26 adopted schedule. SUPERSESSION 2026-09-10: this row cited the FY 2025-26 Adopted Miscellaneous Fees Schedule, whose document URL still returns HTTP 200 but is no longer the schedule the city lists as current. The FY 2026-27 Miscellaneous Fees Schedule was ADOPTED JUNE 2, 2026 and took EFFECT JULY 1, 2026 under Fees Resolution 2026-028, and raised essentially every Building Division amount by about 4 percent. Reference points: permit issuance residential/non-residential $186.83 to $194.30, permit issuance EMP and misc. building $70.06 to $72.86, minimum inspection fee $203.95 to $212.11, minimum plan check $282.75 to $294.06, minimum fee nonresidential $93.40 to $97.14, and the General Plan Update surcharge $28.10 to $29.22. The percentage-based charges (electrical, mechanical and plumbing plan check at 65 percent of subtotal) did not change. All figures below are from the FY 2026-27 adopted edition.
Source: published fee schedule · Verified 11/6/2026
Shed Permit
These lines are alternatives, not a running bill. Pick the one that describes your project and any percentage-based add-ons will be calculated from it.
○Misc. residential structure, patio cover/garage, structural plan check, per sq ft Flat fee $0.53 | $0.53 |
○Misc. residential structure, patio cover/garage, structural inspection, per sq ft Flat fee $0.54 | $0.54 |
○Minimum fee, inspection (flat) Flat fee $212.11 | $212.11 |
○Permit issuance fee, residential and non-residential Flat fee $194.30 | $194.30 |
How this jurisdiction calculates the fee
Santa Ana publishes no dedicated storage-shed permit fee. A shed over the 120 sq ft exemption is priced under item 41/42, Miscellaneous Residential Structure: Patio Cover/Garage, using the per-square-foot structural plan check and structural inspection rates, with electrical billed separately per device if power is run to the structure. The flat permit issuance fee, the General Plan Update surcharge, and the published minimum plan check and minimum inspection floors apply. FY 2025-26 adopted schedule. SUPERSESSION 2026-09-10: this row cited the FY 2025-26 Adopted Miscellaneous Fees Schedule, whose document URL still returns HTTP 200 but is no longer the schedule the city lists as current. The FY 2026-27 Miscellaneous Fees Schedule was ADOPTED JUNE 2, 2026 and took EFFECT JULY 1, 2026 under Fees Resolution 2026-028, and raised essentially every Building Division amount by about 4 percent. Reference points: permit issuance residential/non-residential $186.83 to $194.30, permit issuance EMP and misc. building $70.06 to $72.86, minimum inspection fee $203.95 to $212.11, minimum plan check $282.75 to $294.06, minimum fee nonresidential $93.40 to $97.14, and the General Plan Update surcharge $28.10 to $29.22. The percentage-based charges (electrical, mechanical and plumbing plan check at 65 percent of subtotal) did not change. All figures below are from the FY 2026-27 adopted edition.
Source: published fee schedule · Verified 11/6/2026
Water Heater Permit
These lines are alternatives, not a running bill. Pick the one that describes your project and any percentage-based add-ons will be calculated from it.
○Water heater, residential up to 50 gallons Flat fee $29.45 | $29.45 |
○Water heater, commercial up to 50 gallons Flat fee $29.45 | $29.45 |
○Water heater, residential or commercial over 50 gallons Flat fee $120.82 | $120.82 |
○Water heater, tankless Flat fee $86.79 | $86.79 |
○Plumbing permit issuance fee Flat fee $72.86 | $72.86 |
○Minimum fee (nonresidential) Flat fee $97.14 | $97.14 |
How this jurisdiction calculates the fee
Santa Ana charges a specific per-appliance plumbing fee for water heaters rather than pricing them off valuation, with separate amounts by capacity and type. On top of the appliance fee, a flat plumbing permit issuance fee applies, plus the General Plan Update surcharge, and a nonresidential minimum fee floors commercial permits. A stand-alone plumbing plan check, when required, is 65 percent of the subtotal, though a straightforward water heater changeout does not get plan checked. Note that a separate Solar Energy / miscellaneous section of the schedule also lists lower legacy per-unit water heater amounts. FY 2025-26 adopted schedule. SUPERSESSION 2026-09-10: this row cited the FY 2025-26 Adopted Miscellaneous Fees Schedule, whose document URL still returns HTTP 200 but is no longer the schedule the city lists as current. The FY 2026-27 Miscellaneous Fees Schedule was ADOPTED JUNE 2, 2026 and took EFFECT JULY 1, 2026 under Fees Resolution 2026-028, and raised essentially every Building Division amount by about 4 percent. Reference points: permit issuance residential/non-residential $186.83 to $194.30, permit issuance EMP and misc. building $70.06 to $72.86, minimum inspection fee $203.95 to $212.11, minimum plan check $282.75 to $294.06, minimum fee nonresidential $93.40 to $97.14, and the General Plan Update surcharge $28.10 to $29.22. The percentage-based charges (electrical, mechanical and plumbing plan check at 65 percent of subtotal) did not change. All figures below are from the FY 2026-27 adopted edition.
Source: published fee schedule · Verified 11/6/2026
See the full write-up: Santa Ana building permit cost
Estimate only.Fee schedules change, and building departments set the final valuation and decide which fees apply to your scope. Confirm with the jurisdiction before budgeting. Lines marked “see rule” could not be computed from the published wording and are shown verbatim rather than guessed.