363 ADJUSTMENT POINTS FOR RANGE Sieve Size and Binder Content Adjustment Points (For each 0.1% out of range) No. 8 (2.36 mm) 0.1 No. 30 (600 μm) 0.1 No. 200 (75 μm) 0.1 % Binder 1.0 For mixtures produced during a certified HMA plant’s adjustment period, adjustment points will not be assessed if the mixture produced is in accordance with the following: 1. The gradation complies with 410.05 with the allowable tolerance limits shown in 410.09. 450
2.The range for the binder content and gradation do not exceed the limits shown in 410.09.
3.The binder content is within the tolerance requirements of 410.09. If the mixture is not in accordance with these requirements, adjustment points will be assessed in accordance with 410.09 for variations exceeding the requirements shown above. 460
b.Density When the density of the lot is outside the allowable tolerances, adjustment points will be assessed as follows: DENSITY Percentages are based on %MSG Pay Adjustments, % > 97.0 Submitted to the Division of Materials and Tests* 93.0 – 97.0 0.00 92.0 – 92.9 0.20 points for each 0.10% below 93.0 91.0 – 91.9 2.00 + 0.40 points for each 0.10% below 92.0 89.0 – 90.9 6.00 + 1.00 points for each 0.10% below 91.0 Submitted to the Division of Materials and Tests* * Test results will be considered and adjudicated as a failed material in accordance with normal De partment practice as listed in 105.03.
410.20 Appeals If the QC test results do not agree with the acceptance test results, a request, along
with the QC test results, may be made in writing for additional testing. Additional 410.20 364 testing may be requested for one or more of the following tests: binder content, 470 gradation, or MSG of the mixture samples, and bulk specific gravity of the density cores. The request for the appeal for MSG, BSG of the density cores or binder content and gradation shall be submitted within seven calendar days of receipt of the Department’s written results for that sublot. The sublot and specific tests shall be specified at the time of the appeal request. Only one appeal request per sublot is allowed. Once the appeal request has been granted, the Engineer will perform additional testing. The appeal results will replace all previo us test results for acceptance of mixture in accordance with 410.09 and density in acco rdance with 410.16. The results will be 480 furnished to the Contractor. The backup mixture samples or density cores will be tested in accordance with the following:
a.MSG The backup MSG will be dried in accordance with ITM 572 and mass determined in water in accordance with AASHTO T 209. (b) Binder Content and Gradation The backup binder content and gradation sample will be prepared and tested in accordance with the test methods that were used for acceptance. 490
c.BSG of the Density Core Cores shall be taken within seven calendar days unless otherwise directed. Additional core lo cations will be determined by adding 1 ft longitudinally of the cores tested using the same transverse offset. The cores will be dried in accordance with ITM 572 and tested in accordance with AASHTO T 166, Method A or AASHTO T 331, if required. The Contractor shall clean, dry, and refill the core holes with SMA or HMA surface materials within one wo rk day of the coring operations.
410.21 Method of Measurement 500
SMA mixtures will be measured by the ton of the type specified, in accordance with 109.01(b). The measured quantity will be divided by the MAF to determine the pay quantity. Joint adhesive will be measured by the linear foot in accordance with 109.01(a).
410.22 Basis of Payment
The accepted quantities for this work will be paid for at the contract unit price per ton for QC/QA – HMA, of the type specified, – SMA, complete in place. 510 Payment for furnishing, calibrating, operating the inertial profiler, and furnishing IRI profile information will be made in accordance with 401.18. Furnishing and operating the 16 ft straight edge shall be included in the cost of other pay items within this section. 410.21 365 Joint adhesive will be paid for by the linear foot, complete in place. Adjustments to the contract payment with respect to mixture, density, and smoothness for mixture produced will be included in a quality assurance adjustment 520 pay item. The unit price for this pay item will be $1.00 and the quantity will be in units of dollars. The quantity is th e total calculated in accord ance with 410.19. A change order will be prepared to reflect contract adjustments in accordance with 109.05. Payment will be made under: Pay Item Pay Unit Symbol Joint Adhesive, ____________ ................................................. LFT course type 530 QC/QA - HMA, _____, _____, _____, ______ mm, - SMA .... TON (ESAL (1))(PG(2))(Course(3))(Mix(4)) Quality Assurance Adjustment .................................................. DOL
1.ESAL Category as defined in 410.04
2.Number represents the high temperature binder grade. Low temperature grades are - 22
3.Surface or Intermediate
4.Mixture Designation Preparation of surfaces to be overlaid sh all be included in the cost of other pay 540 items within this section. Coring and refilling of the pavement holes shall be included in the cost of other pay items within this section. No payment will be made for additional anti-stripping additives, appeal coring or related traffic control expenditures for coring operations. Corrections for pavement smoothness sha ll be included in the cost of other pay items within this section. 550 The price for inertial profiler, HMA will be full compensation regardless of how often the inertial profiler is used or how often the IRI is determined.
Source: Indiana Standard Specifications, 2024 Edition. Pages 367–370 of 1,248.