B
HomeLibrariesCode AISearchProjectsBookmarksAddress
FeedbackHelp Desk
Libraries
Estimate & calculate
CalculatorsChecklists
PricingLog in
Earthwork

201Clearing and Grubbing

WY · 2021 Standard Specifications✓ Full text on BuildSpecBook pages 144–0 Save this section

Ask about Section 201

Get a cited answer from the section text. Click the citation to check it.

One cited answer a day is free. Start a 14-day trial for unlimited, no card required.

Clearing and Grubbing

201.1DESCRIPTION

1 This section describes the requirements for clearing, grubbing, removing, and disposing of vegetation and debris.

201.2MATERIALS—V acant

201.3EQUIPMENT—V acant

201.4CONSTRUCTION

201.4.1 General

1 The engineer will establish right-of-way and construction lines and designate vegetation and other objects to remain. Protect from harm or defacement any vegetation and objects designated to remain.

201.4.2 Clearing and Grubbing

1 Clear or grub surface objects, trees, shrubs, plants, stumps, roots, and other protruding obstructions not specified to remain.

2 Fell and remove timber in a way that minimizes damage to riparian habitat.

3 Except in urban areas, stumps outside slope stake limits may remain in place if cut flush with the ground. In urban areas, cut stumps flush and grind to below grade.

4 Backfill with suitable material and compact holes left by removed stumps and other obstructions, in accordance with Subsection 203.4.3, Embankment and Cut Areas with Moisture and Density Control.

5 Unburned refuse and debris become the property of the contractor; remove it from the right-of-way.

201.4.3 Mulching

1 Incorporate brush and existing vegetation that can be used as mulch into the topsoil in accordance with Subsection 207.4.1, Topsoil, Construction, General.

Clearing and Grubbing SECTION 201

201.5MEASUREMENT and PAYMENT

1 The engineer will measure:

1.Clearing and Grubbing by the acre [hectare] or the complete unit. The engineer will

use one or more of the following methods:

1.1Area Basis. By the acre [hectare], within the limits specified or staked by

the engineer.

1.2Lump-Sum Basis. No measurement

2.Clearing Trees in [mm] by the each. Trees less than 4 in [100 mm] in diameter

will be classified as brush. Trees will be classified and measured in accordance with Table 201.5-1, Nominal Tree Size Measuring.

Table 201.5-1 Nominal Tree Size Measuring Diameter of Tree at Height of 24 in [600 mm] (in [mm])

Pay Item Size Designation 4 to 8 [100 to 200] 6 in [150 mm] Over 8 to 12 [201 to 300] 10 in [250 mm] Over 12 to 24 [301 to 600] 18 in [450 mm] Over 24 to 36 [601 to 900] 30 in [750 mm] Over 36 to 60 [901 to 1500] 48 in [1200 mm] Over 60 [over 1500] 60 in [1500 mm]

2 The department will pay as follows:

Pay Item

Pay Unit Measure to the Nearest Pay to the Nearest Clearing and Grubbing LS, ACRE [LS, ha] LS, ft [LS, 0.5 m] LS, 0.01 ACRE [LS, 0.005 ha] Cleaning Trees ____ in [mm] EA [Ea] EA [Ea] EA [Ea]

Get an email when 201 changes

Wyoming revises spec sections through supplementals and new editions. We check this one every week and email you the day it changes. Free, no account.

Source: Wyoming Standard Specifications for Road and Bridge Construction, 2021 Edition. Pages 144–0 of 771. View official source ↗

Ask about this section

Scoped to Wyoming WYDOT Standard Specifications for Road & Bridge Construction, Section 201 — Clearing and Grubbing. Every answer cites the section it came from, with a verification date — don’t trust a percentage, click the citation.