B
HomeLibrariesCopilotSearchProjectsBookmarks
FeedbackHelp Desk
Libraries
Building Codes
Code LibraryIBC — BuildingIRC — ResidentialIFC — FireIPC — PlumbingIMC — MechanicalIFGC — Fuel GasIECC — EnergyNEC — ElectricalModel Codes
Specifications
CSI SpecificationsDOT SpecsTransit SpecsUSACE
Standards
TransportationRailroadFire SafetyAccessibilityStructural
Tools & References
DiagramsAssembliesProductsCalculatorsChecklistsPermits
PricingLog in
General Provisions (00100-00999)

501Portland Cement Concrete Pavement and Base …………..………… 5-1

RI · 2024 Standard SpecificationsBook pages 89View official source ↗

Part 200 — EARTHWORK AND EROSION CONTROL (Continued) Page

Section 210 Stilling Basins for Water Pollution Control …………………..……….. 2-53 Section 211 Construction Accesses ………………………………….….………….. 2-54 Section 212 Maintenance and Cleaning of Erosion and Pollution Controls ………………………………………… 2-55 Section 213 Placement of Millings Beneath Guardrail ………….………….……… 2-59 Section 214 Containment System for Control of Hydrodemolition Runoff and Maintenance and Disposal of Hydrodemolition Runoff ….…. 2-60

Part 300 — Aggregate and Gravel Base and Subbase Courses

Section 301 Aggregate and Gravel Base Courses ………………….…………….. 3-1 Section 302 Gravel Borrow Subbase Courses ……………………….……………. 3-2 Section 303 Special Graded Aggregate for Shaping and Trimming Driveways or Shoulders ……….…………….. 3-3 Section 304 Selected Leveling and Filler Aggregate …………………..………….. 3-4

Part 400 — Bituminous Pavements

Section 401 Dense Graded Hot Mix Asphalt (HMA) Pavements …….…..……….. 4-1 Section 402 Friction Courses…………………………………………….……………. 4-23 Section 403 Asphalt Emulsion Tack Coat …………………………….……………. 4-26 Section 404 Prime Coat ………………………………………………….…………… 4-28 Section 405 Seal Coat …….……………………………………………….…………. 4-30 Section 406 Cold Recycled Base Course (Pavement Rehabilitation/Recycling) ………………………….……… 4-32 Section 407 Hot Recycle Option for Bituminous Pavements …………………….. 4-35 Section 408 Cleaning and Sealing Cracks in Bituminous Concrete Pavements ……………...….………..……….…..….. 4-38 Section 409 Sawing and Sealing Transverse Joints in Bituminous Concrete Pavements Over Rigid Base ……………….……… 4-43 Section 410 Temporary Patching of Potholes and Trenches …………….……….. 4-44 Section 411 Paver Placed Elastomeric Surface Treatment ………………...……. 4-45 Section 412 Rubberized Asphalt Chip Sealing ……………………………….…….. 4-49 Section 413 [Section Not Used] …………………………………………….……….. 4-53 Section 414 Warm Mix Additive ………………………………………….………….. 4-54

Part 500 — Concrete Pavements

Section 502 Full Depth Cleaning and Sealing of Joints and Cracks Two and One-Half (2 ½) Inches Nominal Width or Less in Portland Cement Concrete Pavement ……………..…….. 5-13 -iv-

Part 500 — CONCRETE PAVEMENTS (Continued) Page

Section 503 Repairing Deteriorated/Damaged Joints Greater Than Two and One-Half (2 ½) Inches and Less Than or Equal to Eight (8) Inches Nominal Width in Finished Portland Cement Concrete Pavement ……………………….. 5-14 Section 504 Pavement Grooving …………….………………………………………. 5-18 Section 505 Portland Cement Concrete Base Course w/Crack Control 8-Inch Extra Strength …….………………… 5-19

Part 600 — Concrete

Section 601 Portland Cement Concrete ……………………………………..……… 6-1 Section 602 Mineral Additives for Portland Cement Concrete …….……….…….. 6-34 Section 603 Controlled Low Strength Material (CLSM) ……………….…….…….. 6-36 Section 604 [Section Not Used] ……………………………………………….....….. 6-40 Section 605 Concrete with Calcium Nitrite Based Corrosion Inhibitor ……..…….. 6-40 Section 606 Self Consolidating Concrete (SCC) …………………………….…….. 6-41 Section 607 Mass Concrete ………………………………………………………….. 6-42

Part 700 — Drainage and Selected Utility Accessories

Section 701 Culverts and Storm Drains ………………………….………….……… 7-1 Section 702 Manholes, Inlets and Catch Basins …………...........................……. 7-8 Section 703 Underdrains and Combination Drains ………………………….…..… 7-11 Section 704 Reconstruct Catch Basins and Manholes …………………….……… 7-13 Section 705 Reconstruct Existing Type “D” Catch Basin To Catch Basin with Gutter Inlet ……………………….…….. 7-14 Section 706 Plug and Cap Pipe – All Sizes …………………………………..…….. 7-15 Section 707 Adjust Drainage and Utility Structures ……………………….……….. 7-16 Section 708 Cleaning and Flushing Pipes and Drainage Structures …….………. 7-18 Section 709 Concrete for Thrust Blocks, Headwalls and Miscellaneous Purposes ………………………….….……….. 7-19 Section 710 Cut-Ins for Manholes, Catch Basins and Pipe …………….…….…… 7-20 Section 711 Paved Waterways ………………………………………………………. 7-22 Section 712 Water and Gas Gate Boxes ………………………………….………… 7-24 Section 713 Adjust Curb Stop, Water Gate and Gas Gate Boxes ….....…….….… 7-25 Section 714 Post Type Hydrants …………….…………………………..…………… 7-26

Part 800 — Bridge Structures

Section 801 General ……………………………………………….…………………. 8-1 Section 802 Temporary Bridges ………………………………….…………………. 8-2 Section 803 Removal of Existing Bridges …………………………………………. 8-3 Section 804 Driven Piles …………………………………………………………….. 8-4 Section 805 Earth Retaining Systems ……………………………………………… 8-28 -v-

Source: Rhode Island Standard Specifications (Bluebook), 2024 Edition. Pages 89 of 826.